|
Size: 3596
Comment:
|
Size: 3098
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 3: | Line 3: |
| = General Strategies = | |
| Line 11: | Line 12: |
| Example 1: Metal in the mouth (dental retainer) that moves when the subject breathes. | = Example 1: Metal in the mouth = Here the subject has metal dental work that moves when he breathes. |
| Line 13: | Line 15: |
| Identify the artifact and channel(s) that are most affected. Scanning though the data and performing a PSD can help with this: {{/brainstorm//brainstorm/attachement%3Adental_breathing_artifacts.png%3Faction%3Dcontent?action=content|attachement:dental_breathing_artifacts.png|width="100%"}} | The first step is to identify the artifact and channel(s) that are most affected. After scanning though the data, it appears there are some artifacts present throughout the recording. |
| Line 15: | Line 17: |
| Channel MRT57, on the MEG traces shows the effect of the metal. In addition, this channel has high power in the lower freq (PSD) and the topography shows a dipole below the posterior part of the sensor array. | {{attachment:dental_and_sensor_artifacts.png||height="500",width="600"}} |
| Line 17: | Line 19: |
| Since the artifact is ongoing and not necessarily a well-defined 'event', we will use the first strategy. | First, slower perturbations in the posterior temporal areas, as seen in the channels highlighted in red. Then there are sharp 'jumps', highlighted in blue, which do not seem to be physiological, but instead are most likely sensor noise. We can also see artifacts from the heart. In addition, performing a power spectrum density (PSD) helps identify the channels and the frequencies which are most affected by these artifacts. {{attachment:PSD_topo_artifacts.png||height="250",width="600"}} The temporal channels have higher power in the lower freq ([0,6]Hz) and the topography shows a dipole below the posterior part of the sensor array. Since the slower artifact is ongoing and not necessarily a well-defined 'event', we will use the first strategy. |
| Line 21: | Line 31: |
| *Event name: empty *Event window: ignore this *Frequency band: from the PSD I can see that the artifact is mostly defined in [0.5,10]Hz. If you know the freq band of the artifact, you should adjust this accordingly, if not, you can use a more broadband to get an overall view. *Sensor types: MEG *Compute using existing: uncheck this box *Save averaged artifact: uncheck this box *Method to calculate: choose PCA |
* Event name: empty * Event window: ignore this * Frequency band: from the PSD I can see that the artifact is mostly defined in [0.5,10]Hz. If you know the freq band of the artifact, you should adjust this accordingly, if not, you can use a more broadband to get an overall view. * Sensor types: MEG * Compute using existing: uncheck this box * Save averaged artifact: uncheck this box * Method to calculate: choose PCA |
| Line 29: | Line 39: |
| 1. Review the resulting projectors and find component(s) that eliminates the artifact. Be sure to review the topography and the time series of the component to be sure you are only removing the artifact. After selecting the first component, I see that the second one is not appropriate since it contains a dipole over the auditory regions. 1. Check for additional artifacts. I see that there is still some artifacts left on channel MLT57 and so I mark these as events (event type artifact_MLT57). This can be done using the generic event detection on that specific channel or they can be marked manually. 1. Compute an SSP projection on these artifacts, but use the second strategy where the artifact is an event. * Time window: this should be the time window of the entire recording *Event name: artifact_MLT57 *Event window: here is see these more discrete events are lasting about 400-500ms, so I choose an event window to be [-200,200]ms. *Frequency band: again, this artifact is mostly defined in [0.5,10]Hz. *Sensor types: MEG *Compute using existing: check this box because now we want to find what is left after the continuous component is removed *Save averaged artifact: uncheck this box *Method to calculate: I chose PCA (Here you can choose either PCA or average. Try both since one may work better than the other). 1. Select the appropriate topography. Here I chose the first two. 1. Now do the same for cardiac events. Select the appropriate component. Here I chose the first one only. |
1. Review the resulting projectors and find component(s) that eliminate the artifact. Be sure to review the topography and the time series of the component to confirm you are only removing the artifact. {{attachment:eight_components_PCA.png||height="400",width="600"}} We can see here that the first two components are most likely artifacts. Selecting these two does a very good job of removing the artifact. 1. #4 Now do the same for cardiac events. Select the appropriate component. Here I chose the first one only. {{attachment:cardiac_artifact_before.png}} |
Removing artifacts from MEG recordings using Signal Space Projections can sometimes be very efficient. Here are a few tricks to help you remove artifacts from your data that are ongoing or repeating.
General Strategies
We typically use one of three strategies to define an SSP projector:
1. PCA analysis over one continuous epoch (i.e. the entire recording), for which the artifact is ongoing
2. PCA analysis for concatenated 'events', for which the artifact is discrete and repeating in the recording
3. Visual identification of one topography that represents the artifact and is converted to an SSP projector.
Example 1: Metal in the mouth
Here the subject has metal dental work that moves when he breathes.
The first step is to identify the artifact and channel(s) that are most affected. After scanning though the data, it appears there are some artifacts present throughout the recording.
First, slower perturbations in the posterior temporal areas, as seen in the channels highlighted in red. Then there are sharp 'jumps', highlighted in blue, which do not seem to be physiological, but instead are most likely sensor noise. We can also see artifacts from the heart.
In addition, performing a power spectrum density (PSD) helps identify the channels and the frequencies which are most affected by these artifacts.
The temporal channels have higher power in the lower freq ([0,6]Hz) and the topography shows a dipole below the posterior part of the sensor array.
Since the slower artifact is ongoing and not necessarily a well-defined 'event', we will use the first strategy.
- Using the Artifacts menu, select SSP: Generic
- Time window: this should be the time window of the artifact. Here I use the first 100 seconds of the recording since the event is well defined in this time, but you can use longer times to better define the event if necessary.
- Event name: empty
- Event window: ignore this
- Frequency band: from the PSD I can see that the artifact is mostly defined in [0.5,10]Hz. If you know the freq band of the artifact, you should adjust this accordingly, if not, you can use a more broadband to get an overall view.
- Sensor types: MEG
- Compute using existing: uncheck this box
- Save averaged artifact: uncheck this box
- Method to calculate: choose PCA
- Run the process
- Review the resulting projectors and find component(s) that eliminate the artifact. Be sure to review the topography and the time series of the component to confirm you are only removing the artifact.
We can see here that the first two components are most likely artifacts. Selecting these two does a very good job of removing the artifact.
- #4 Now do the same for cardiac events. Select the appropriate component. Here I chose the first one only.
